https://lifescienceglobalca.com/index.php/jcst/issue/feed Journal of Coating Science and Technology 2023-12-20T16:13:08+00:00 Support Manager support@lifescienceglobal.com Open Journal Systems <p><span style="color: #333333;"><span style="font-family: arial,helvetica,sans-serif; font-size: 10pt;"><span>The Journal of Coating Science and Technology (JCST), is an international scientific peer-reviewed journal specializing in the fundamental and applied science of coating materials and surface engineering. The journal aims to provide a forum for the disseminations and exchanges of scientific and technological knowledge based on original research works among those linked to advanced coatings study, development and/or production, focusing in different areas such as wear-resistant coatings, corrosion protective coatings, optical protective coatings, films for biomedical and energy purposes, decorative coatings, and others, produced by advanced techniques such as PVD, CVD, thermal projection, etc.</span></span></span></p> https://lifescienceglobalca.com/index.php/jcst/article/view/9233 Simulation and Experiment Analysis of Driveshaft 2023-08-30T14:56:05+00:00 Jia Hao Li 1281720007@qq.com Yao Liu liuyao@nuc.edu.cn Yang Zhou 1642387517@qq.com You Zhe Wang 1806573182@qq.com Zhan Ling Guo 245239531@qq.com Bin Shen binshen@zgjczg.com <p>A driveshaft is a small spring coil less than 1mm in diameter, composed of several stainless-steel wire filaments. In intervention, the driveshaft is used to transmit force and motion to the inside body through the existing micro channels (such as arteries, veins, and gastrointestinal tract). The performance of the driveshaft determines the efficiency, stability, and accuracy of force and motion transitions, the ability to pass through tortuous microchannels, and the damage to healthy tissues. To determine the influence of fabrication parameters (filament, wire diameter, and outer diameter) on the mechanical properties (such as bending stiffness and natural frequency) of the driveshaft, a simulation was established in ABAQUS to calculate the deformation displacement under 0.0098N and first-order natural frequency. Then, the bending stiffness is calculated. The results show that the bending stiffness and the first-order natural frequency of the driveshaft increase with the increase of the filament number and wire diameter, and with the outer diameter of the driveshaft increases, the bending stiffness increases, while the first-order natural frequency decreases. Finally, the simulation model is verified by measuring the deformation displacement in the experiment. This study provides a methodology for designing and selecting the driveshaft in Interventional therapy.</p> 2023-08-30T00:00:00+00:00 Copyright (c) 2023 https://lifescienceglobalca.com/index.php/jcst/article/view/9413 Pycnometric-Additive Determining of the Degree of Coating of High-Strength Synthetic Diamond Grinding Powders using the Actual 3D Morphology of their Grains 2023-12-20T16:13:08+00:00 G.A. Petasyuk petasyuk@ukr.net O.O. Bochechka bochechka@ism.kiev.ua V.I. Lavrinenko info@lifescienceglobal.com V.G. Poltoratskyi info@lifescienceglobal.com Yu.V. Syrota info@lifescienceglobal.com V.P. Bilochenko info@lifescienceglobal.com <p>The methodological components of direct and indirect analytical determining of the degree of coating of synthetic diamond grinding powders are analyzed. It has been established that the weight method most used in practice for determining this technological property of grinding powder is not universal for different methods of applying the coating. More universal in this regard, as the review of publications showed, is the well-known indirect-analytical method based on the pycnometric-additive approach. An improved variant of this method is proposed, aimed at application to high-strength synthetic diamond grinding powders. The method takes into account the peculiarities of the 3D morphology of the grains of such powders. Using the example of grinding powder AC300 500/400, the grains of which were coated with a solution of a mixture of boron oxide, sodium silicate, and titanium carbide, the advantages of using the proposed method are illustrated. The results of a comparison of determining the degree of coating by a known method and its improved variant are presented.</p> 2023-12-20T00:00:00+00:00 Copyright (c) 2023